Rough In means to bring in the various lines (Plumbing pipes, duct work, electrical conduit) to the space, but not make the final connections. For plumbing, this would be the pipes in the walls and floors that lead to the sinks, bath, toilets, etc, but not actually hooking up those fixtures.
What is a king stud in framing?
Jack studs and king studs. The header is supported by a jack stud at each end. Jacks, sometimes called trimmers, fit under each end of a header, and they transfer the load that the header carries down to the bottom plate and the framing beneath.
To find out your toilet's rough-in, measure from the wall behind the toilet to the middle of the closet bolts, which hold your toilet to the floor. That distance will likely be a bit more than the standard 10″, 12″, or 14″ rough-in dimensions. Round your measurement down to the nearest standard rough-in.
It is the time when access to the space between the studs, floor joists, ceiling joists and every other nook and cranny is most easily accessed. Rough-in refers to the rough installation of the electrical wiring, boxes, fixture mounts, breaker panel, and sub panels.
Plumbers work with three basic categories of supplies. There are the supply pipes, that deliver the clean water into the house and to the plumbing fixtures, such as the sinks, toilets, and washing machine. There are the waste pipes that drain the water and waste from the fixtures.
What is a rough-in inspection? Rough-in inspections are simply inspections of portions of the wiring system that will be concealed when the project is completed. With proper planning, most 1, 2, and 3 family residential jobs only require one rough-in inspection.
Toilet rough in measuring: from wall to bolt cap. When talking toilets, the toilet rough in is the distance from the wall behind the toilet to the center of the outlet pipe where the waste leaves the toilet. The most common distance is 12 inches, so most toilets have a “12-inch rough.”
Carpentry is a building trade concerned with the constructing, assembling, and repairing of wooden structures. Rough carpentry is work done on the framing of a building, including, but not limited to, such basic things as the walls, floor, and roof.
The hard part about plumbing is the rough-in. The last step of connecting the sink, toilet, or tub is almost superfluous. Get the rough-in right and you are 90% of the way there. Below are generally accepted plumbing rough-in measurements for sinks, toilets, and tub/showers.
some use the term "rough" for all the buried materials, including HVAC, electrical, plumbing, framing, low voltage. it is the inspection prior to insulation, then wall covering. generally, a top out is for high rises or multi-story construction. "
Term. Definition. Plumbing trim. Work performed by the plumbing contractor to get the home ready for a final plumbing inspection. Includes installing all toilets (water closets), hot water heaters, sinks, connecting all gas pipe to appliances, disposal, dishwasher, and all plumbing items.
Term. Definition. Electrical Trim. Work performed by the electrical contractor when the house is nearing completion. The electrician installs all plugs, switches, light fixtures, smoke detectors, appliance "pig tails", and bath ventilation fans, wires the furnace, and "makes up" the electric house panel.
plumbing trim is the plumbing work that can be completed after the interior walls are closed and finished. plumbing trim includes installation of plumbing fixtures and faucets.
In this picture it is vented exactly the same as the first example only you will not have the option to tie in the drain to the vertical leg. Also the wet vent area (shared drain and vent section of pipe) can remain 1.5″ if both the sink and shower traps are also 1.5″.
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
Toilets. You need at least 30 inches (76 centimeters) of clear width for toilets, but 32 to 36 inches (81 to 91 centimeters) is much better for most people. Single sinks. For a single sink, you need at least 30 inches (76 centimeters) of width, but 36 to 48 inches (91 to 107 centimeters) is more comfortable.
A full bathroom usually requires a minimum of 36 to 40 square feet. A 5' x 8' is the most common dimensions of a guest bathroom or a master bathroom in a small house. If you happen to have this standard-sized small bathroom, there are two different layouts you can consider.
Total height of one piece gravity toilet might vary from 21 to 30 3/4 inches (53 – 78 centimeters) with 14” – 16” (356 – 406 mm.) distance from the floor to bowl rim. Depth usually stays within 27” – 30” (686 – 762 mm) and width very rarely exceed 20 in (508 mm).