AnswersDriveWhen your Time Warner cable box boots up, it displays various messages on the front of the box. While it's trying to detect a signal coming from the cable input, the box displays Alt, which means "wait." Check your connections, reboot your cable box and then call Time Warner support if you can't resolve the problem.
What does it mean when your cable box says Hunt?
In this case, the "HUNT" message typically means that the box is searching for a signal - you can usually get rid of this message by power cycling the box. To do that you can unplug the power for 30 seconds or so.
1
How do you reset a spectrum cable box?
To reset or power cycle your receiver, unplug it for 15 seconds and then plug it back in. Wait up to 20 minutes for the receiver to fully recover before turning it back on. If you're still having difficulty, contact us at (833) 267-6094.
2
How do you reset Spectrum cable box?
To reset (power cycle) your receiver, unplug it for 15 seconds and then plug it back in. Wait up to 20 minutes for the receiver to fully recover and turn it back on.
3
How do you reset your cable box?
Option 1
- Unplug your cable box from either the wall outlet or the box itself.
- Wait 5 seconds and plug it back in.
- During the reboot process, the cable box may display a series of numbers, characters or letters.
- When the front panel on the cable box displays "Turn On", the reboot is complete.
4
What does it mean when your cable box says Hunt?
In this case, the "HUNT" message typically means that the box is searching for a signal - you can usually get rid of this message by power cycling the box. To do that you can unplug the power for 30 seconds or so.
5
How do you reboot an optimum cable box?
To reset your cable box, simply unplug it from the wall outlet. Wait about 30 seconds, then plug it back in and allow the box to go through the reboot process, which should take about three minutes. If you can't reach your power cord, reset your cable box this way: Turn the cable box power on.
6
How do you hook up a cable box?
Use the coaxial cable to connect your cable wall outlet to the IN input on the back of the HD Set-Top Box/DVR. Using the HDMI cable, plug one end into the HDMI output on the back of the HD Set-Top Box/DVR, and the other end into the HDMI input on the back of your TV.
8
How do I reset my Time Warner cable box?
I. Turn off your cable set-top box (using either the remote or the button on the front of the box). II. Carefully unplug the power cord from either the wall or the back of the cable set-top box. If it is plugged into a power strip, turn off the power strip at the switch on the top of the strip.
9
How do you fix your TV when it says no signal?
If the source is correct from step two:
- Unplug the HDMI cable from your Bell MTS Fibe TV Set-top Box.
- Wait 30 seconds.
- Plug the HDMI cable back in.
- Wait for the signal to initialize.
- Make sure all cables connected on the set-top box and your TV are secure.
10
Why does my TV glitch?
General pixilation and freezing occurs when there is a disruption in the TV signal, or there is a weak signal altogether. Check your connections: Unplug the HDMI cable from your Bell MTS Fibe TV Set-top Box. Make sure all cables connected on the set-top box and your TV are secure.
11
How do I hook up my spectrum cable?
You can connect your high-definition (HD) Spectrum Receiver (cable box) to your HDTV using either HDMI or component cables. To get started: Connect the power cord to the back of the receiver and plug it into a wall outlet. Connect the coaxial cable between the cable wall outlet and the Cable In port on the HD receiver.
12
How do I reset my spectrum modem?
The steps listed should work correctly for all modem types.
- Turn off your computer.
- Unplug the power cord from the back of the modem and remove any batteries.
- Wait 30 seconds, then place the batteries back in the modem and reconnect the power.
- The modem connection lights will be solid (not blinking).
13
What is the error in the code?
In computer programming, a return code or an error code is an enumerated message that corresponds to the status of a specific software application. They are typically used to identify faults, such as those in faulty hardware, software, or incorrect user input.
14
How do you reset a Comcast cable box?
Reboot Using the Power Button
- Ensure your cables are tightly secured.
- Press and hold the Power button located on the front of the TV Box for 10 seconds.
- The TV Box should automatically reboot.
15
How do I reset my modem and wireless router?
Unplug the router first, then unplug the modem. Neither of them have power buttons, so it's a matter of pulling the power cord out of the back of the modem or router. Count down to 10, then plug the modem back in and then the router next. Give them both time to boot up and connect by watching the activity lights.