In the east, the average cost for driveway sealing is typically between $.10-$.16 per square foot. So for a 1000 sq. ft. driveway it will cost between $100-$160. In the upper-midwest, many driveway contractors charge per 1000 sq. ft., typically between $85-$100 per 1000 sq. ft. with a minimum charge of $100.
Besides, how much does it cost to clean and seal pavers?
Taking these variables into consideration and giving a very rough idea on cost to clean and seal pavers per square foot you would be in the range of .90 to $2 per square foot. An average sized patio is in the range of $1.35-$2 for the thorough power wash, install polymeric sand ad seal with a wet look sealer.
How many square feet does a 5 gallon bucket of driveway sealer cover?
5-Year Driveway Sealer and Filler - 5 Gallon :: Driveway - Asphalt :: FarmPaint.com. Coverage: Approximately 250-350 square feet per 4.75 Gallon container.
The temperature should not drop below 60° F during the curing process (24 hours). Don't wait until fall to seal the driveway from ice and snow, in fact it's important to seal it against rain and UV rays that can damage asphalt and create cracking and crumbling.
The average sealcoating cost for an asphalt parking lot with either asphalt or coal tar emulsion pavement sealer ranges from $0.14 - $0.25 per square foot.
Ignoring any maintenance costs, asphalt is generally much cheaper to install than concrete. On average, the cost per square foot for asphalt will run between $2.50 to $4.00. Fluctuations in crude oil prices can cause fluctuations in asphalt prices but the price will remain around this range.
Sealcoating the asphalt, seals the small cracks that can turn into large cracks and prevents water from seeping down to the base material. Sealcoat that is applied correctly makes your asphalt driveway look cleaner because rain washes dirt and debris easily away from the smooth, non-porous surface.
In full sun, you can walk on it in a few hours but you can not drive on it for 24 hours. In the spring and fall, 48 hours is recommended. The driveway surface dries in 24 hours but takes 30 days to cure.
A. It is recommended that you seal your stamped concrete at least every two years. It is not necessary to seal every year. If you begin to notice the color starting to loose its intensity it is time to seal. When applying sealer it is best to apply it in 2 thin coats opposed to one thick coat.
In terms of bulk price, asphalt is priced by the ton. One ton of asphalt covers about 80 square feet with 2 inches of material or 160 square feet with 1 inch of material. Current wholesale pricing of bulk base-grade asphalt is $70-$80 per ton; top-layer grade is $75-$85 per ton.
Cost of Resurfacing. Resurfacing usually costs anywhere from $1 to $2 per square foot. The price varies based on factors such as your geographic location, local competition, the season and the condition of your driveway. So the cost to resurface a 3,000 square foot driveway would be anywhere from $3,000 to $6,000.
Asphalt driveways typically last 12 to 20 years, depending on the quality of the installation, the climate, the usage they get, and how well they have been maintained. Like most everything else, the better care you take of your asphalt driveway the longer it will remain in service.
According to our concrete slab material estimator, the average minimum cost per square foot of a concrete slab is $1.36 and the maximum is $1.88. By comparison, the price per square foot for a cement slab is $5.50.
In many cases a 4-inch thickness may be adequate, but 5 or even 6 inches of full-depth asphalt will assure you of a stronger, stable driveway under a wider range of climate and loads. As an option, some contractors use 6 to 8 inches of compacted aggregate, or gravel, as a base for 3 inches of asphalt pavement.
Explanation: During the summer months of May through August we recommend staying off the driveway with vehicles for 48 hours. After September 1st allow 72 hours or more depending on the temperature. Driveway sealer will dry like paint from the top down. It may feel dry on the surface but may still be wet underneath.
Chances are these slabs weren't poured over an unstable base, but rather, frost heaving moved them. Each individual slab can move at the expansion joints, and if you have an unstable base, the condition can occur more often. A concrete pavement that moves will damage any asphalt overlay over time.
NAPA estimates an average asphalt density of 145 pounds per cubic foot, or 3,915 pounds per cubic yard. For example, if your calculated volume is 25 cubic yards, multiplying 25 by 3,915 will give you an asphalt weight per cubic yard of 97,875 pounds, or about 49 tons.
Start at your garage or carport and work toward the street. Using a driveway squeegee tool, spread a very thin layer of sealer moving down the length of the driveway. Apply the second coat from one edge to the other in a perpendicular manner. Make sure the coats overlap and cover 100% of the asphalt surface.
Paving a typical two-car concrete driveway of 16 feet wide and 38 feet long (610 sq. ft.) without curves or slopes costs $3,040. Therefore, the average cost per square foot amounts to $4.99, although it can be higher if excavation is needed.
Depending on the temperature and humidity of the air, you should keep vehicles off the new surface for 48 to 72 hours. You may walk on your driveway within 24 hours. After walking across fresh seal coat, please check the bottom of your shoes, or remove shoes before entering into your home.
The general range for a cubic yard of plain pea gravel is about $30 to $35, and a ton will cost about $40 to $45. For a colored variety, expect to add an extra $20 to $50 to those prices. If you buy in bulk, or 10 or more tons at a time, you may be able to get the price down to as low as $15 to $20 per ton.
The Means to Maintain. As I mentioned, it's much less expensive to maintain existing roadways. To mill and resurface a 4-lane road, it costs an average of $1.25 million per mile. Then, if you want to expand said road from four lanes to six, you can expect to pay roughly $4 million.
Asphalt driveway sealer, which sits on top of the driveway, acts as a barrier that prevents water, ice, car fluids, the sun, salt and other chemicals from staining and eating away at the surface of the driveway. The frequency with which you should use driveway seal will vary based on your location.